Does anyone have a config file that is plain jane just to get bink up and running...

I use to have one a while back... and don't have a clue how to make it work with out that file..

Thanx

Joe

... Platinum Xpress & Wildcat!..... Nice!!!!
--- Platinum Xpress/Win/WINServer v3.0pr5
* Origin: Joe's Computer & BBS, Crystal River, Fl. -= telnet.joe (1:275/312)

Replying to a message from IB JOE 1:275/312 to ALL,

About Config File, On Mon Feb 10 2003

Does anyone have a config file that is plain jane just to get bink
up and running...

A little fancier than plain jane but will get you up and running, I used this for years with a USR Sportster 28.8.

; BINKLEY CONTROL FILE
;
Serial 1234
System Your BBS Name Here
Sysop Your Name Here
Address Your Node Number Here
MyLocation Your Location as it appears in the Nodelist
MyPhone +1-Finish your Phone Number
MyListFlags Your Nodelist Flags Here
ExtBaudRates
MyMaxBaud 57600
LockBaud
PickUpAll
Banner Welcome to Your BBS
EnterBBS Press Esc to enter the system or wait a few seconds. BBSNote Thank you, now loading Maximus ...
DoingMail Sorry; we are currently running a required 2:00-3:00 A.M. mail-only
event. Shell 1 c:\timed\timed.com
Shell 2 Bonk
Shell 3 MFM -ac:\BBS
Shell 4 UEDIT
Shell 5 IN.bat
Shell 6 Out.bat
Shell 7 Qedit c:\bbs\question.txt
Shell 8 LIST \bbs\INFO.log
Shell 9 DEL c:\mail\outbound\*.$$?
; CHANGE THE FOLLOWING TO SUIT YOUR NEEDS

StatusLog c:\BBS\Binkley.log
Downloads e:\Private\
CaptureFile c:\BBS\Binkterm.cap
NetMail i:\Echo\
NetFile c:\Mail\Inbound\
Hold c:\Mail\Outbound\
Version7
LogLevel 5
Gong
;
; Not all systems can handle the stresses of the Janusbaud bi-directional ;
protocol. If you experience problems, comment out the line below. ;
JanusBaud 57600
;
Unattended
Polltries 150
Nodelist c:\Nodelist\
MaxReq 10
MaxBytes 2900000
About c:\BBS\Error.txt
Okfile c:\BBS\OKfile.lst
Avail e:\New\ALLMARSH.zip
ReqOnUs
Timeout 20
BBS Batch
ScreenBlank call
Colors 112 14 10 11 7 12 112 3
Boxtype 2
CursorCol 1
CursorRow 25
;
; Binkley 2.50 specific
Serial 12345
StartBlkLen 512
BlankWait 60
MaxTime 60
RingTries 3
;
; Binkley 2.55 specific
FileSec 3
MaxAreas c:\bbs\area.dat
;
; Binkley 2.59 specific
;ModemRetry <modem response>
;AltNumber <primary number> <alternate number>
;==========================[ MODEM SETUP SECTION ]============================ Port 2
Baud 57600
Carrier 80
Init v~^~ATH0|`AT&F1|~ATM0&K1&S1S2=127S7=90S9=30S10=20S11=50|`ATS15=8S28=20|``AT+FCLASS=0|` Prefix ~AT+FCLASS=0DT
Suffix `
Answer ```AT+FCLASS=2\.0|`AT+FBO=1;+FAA=1;+FNR=1,1,1;+FLI="+1-250-786-7921";A|

;In the above when receiving with Binkley: +FBO=1
;In the above when receiving with BGFax: +FBO=0
;
PreDial `
PreInit |v``^``|
DTRHigh
;
; Add the following responses to Binkley.cfg in the same order! Also ; be sure
to physically creade the sub-directory in FaxInDir ;
ModemIgnore +FDM
ModemIgnore RINGING
ModemIgnore RING RESPONSE
ModemRinging RING
ModemConnect CONNECT
ModemIgnore RRING
ModemFailure BUSY
ModemFailure VOICE
ModemFailure ERROR
ModemFailure OK
ModemFailure NO CARRIER
ModemIncoming NO DIAL TONE
ModemIgnore DIALING
ModemFailure NO ANSWER
ModemIgnore DIAL TONE
ModemFax +FCO
FaxInDir C:\BGFAX\IN
;
; AfterCall 34 ATI6I11|ATZ| ; ) Just a bunch of samples of the ; AfterCall 18 ATI6| ; ) AfterCall function to record modem ; AfterCall 14 ATI11| ; ) stats in Binkley.log


I am also assuming that you are using some flavour of DOS. Some modifications will be needed for OS/2.

Hope this helps. Keep us posted.

We are a fine board trying to make it better.
http://www.pris.bc.ca/ghannah
ghannah@pris.bc.ca
Cheers! Gord
-=Team OS/2=-
--- Timed/2 2.30+
* Origin: Marsh BBS (c), Dawson Creek, BC Canada (1:17/23.1)

No, that was plain enough....

I have a few questions though...

I want to use this to call only a few boards... Maybe just a point address.
Is there a simple way to configure just a few system to call out on??

I have a copy of XLaxNode ... what is the command line to get that to compile
a nodelist??

Thanx

Joe





On Feb 11, 2003 08:19am, GORD HANNAH wrote to IB JOE:

Replying to a message from IB JOE 1:275/312 to ALL,

About Config File, On Mon Feb 10 2003

Does anyone have a config file that is plain jane just to get bink
up and running...

A little fancier than plain jane but will get you up and running, I
used this for years with a USR Sportster 28.8.

; BINKLEY CONTROL FILE
;
Serial 1234
System Your BBS Name Here
Sysop Your Name Here
Address Your Node Number Here
MyLocation Your Location as it appears in the Nodelist
MyPhone +1-Finish your Phone Number
MyListFlags Your Nodelist Flags Here
ExtBaudRates
MyMaxBaud 57600
LockBaud
PickUpAll
Banner Welcome to Your BBS
EnterBBS Press Esc to enter the system or wait a few seconds. BBSNote Thank you, now loading Maximus ...
DoingMail Sorry; we are currently running a required 2:00-3:00 A.M. mail-only event. Shell 1 c:\timed\timed.com
Shell 2 Bonk
Shell 3 MFM -ac:\BBS
Shell 4 UEDIT
Shell 5 IN.bat
Shell 6 Out.bat
Shell 7 Qedit c:\bbs\question.txt
Shell 8 LIST \bbs\INFO.log
Shell 9 DEL c:\mail\outbound\*.$$?
; CHANGE THE FOLLOWING TO SUIT YOUR NEEDS

StatusLog c:\BBS\Binkley.log
Downloads e:\Private\
CaptureFile c:\BBS\Binkterm.cap
NetMail i:\Echo\
NetFile c:\Mail\Inbound\
Hold c:\Mail\Outbound\
Version7
LogLevel 5
Gong
;
; Not all systems can handle the stresses of the Janusbaud bi-directional ; protocol. If you experience problems, comment out the line below. ; JanusBaud 57600
;
Unattended
Polltries 150
Nodelist c:\Nodelist\
MaxReq 10
MaxBytes 2900000
About c:\BBS\Error.txt
Okfile c:\BBS\OKfile.lst
Avail e:\New\ALLMARSH.zip
ReqOnUs
Timeout 20
BBS Batch
ScreenBlank call
Colors 112 14 10 11 7 12 112 3
Boxtype 2
CursorCol 1
CursorRow 25
;
; Binkley 2.50 specific
Serial 12345
StartBlkLen 512
BlankWait 60
MaxTime 60
RingTries 3
;
; Binkley 2.55 specific
FileSec 3
MaxAreas c:\bbs\area.dat
;
; Binkley 2.59 specific
;ModemRetry <modem response>
;AltNumber <primary number> <alternate number> ;==========================[ MODEM SETUP SECTION ]============================ Port 2
Baud 57600
Carrier 80
Init v~^~ATH0|`AT&F1|~ATM0&K1&S1S2=127S7=90S9=30S10=20S11=50|`ATS15=8S28=20|` `AT+FCL ASS=0|` Prefix ~AT+FCLASS=0DT
Suffix `
Answer ```AT+FCLASS=2\.0|`AT+FBO=1;+FAA=1;+FNR=1,1,1;+FLI="+1-250-786-7921";A|

;In the above when receiving with Binkley: +FBO=1
;In the above when receiving with BGFax: +FBO=0
;
PreDial `
PreInit |v``^``|
DTRHigh
;
; Add the following responses to Binkley.cfg in the same order! Also ;
be sure to physically creade the sub-directory in FaxInDir ;
ModemIgnore +FDM
ModemIgnore RINGING
ModemIgnore RING RESPONSE
ModemRinging RING
ModemConnect CONNECT
ModemIgnore RRING
ModemFailure BUSY
ModemFailure VOICE
ModemFailure ERROR
ModemFailure OK
ModemFailure NO CARRIER
ModemIncoming NO DIAL TONE
ModemIgnore DIALING
ModemFailure NO ANSWER
ModemIgnore DIAL TONE
ModemFax +FCO
FaxInDir C:\BGFAX\IN
;
; AfterCall 34 ATI6I11|ATZ| ; ) Just a bunch of samples of the ; AfterCall 18 ATI6| ; ) AfterCall function to record modem ; AfterCall 14 ATI11| ; ) stats in Binkley.log

I am also assuming that you are using some flavour of DOS. Some modifications will be needed for OS/2.

Hope this helps. Keep us posted.

We are a fine board trying to make it better. http://www.pris.bc.ca/ghannah
ghannah@pris.bc.ca
Cheers! Gord
-=Team OS/2=-
--- Timed/2 2.30+
* Origin: Marsh BBS (c), Dawson Creek, BC Canada (1:17/23.1)

... Joe's Computer & BBS -=telnet.joesbbs.com=-
--- Platinum Xpress/Win/WINServer v3.0pr5
* Origin: Joe's Computer & BBS, Crystal River, Fl. -= telnet.joe (1:275/312)

Replying to a message from IB JOE 1:275/312 to GORD HANNAH,

About RE: Config File, On Tue Feb 11 2003

I have a few questions though...

I want to use this to call only a few boards... Maybe just a point
address. Is there a simple way to configure just a few system to
call out on??

If you want Bink setup as a point front end that can be done real easy. Two ways get a copy of PPOINT and it will set it up for you or try this it was setup with PPOINT:

;=========================================================================== ;Binkley Configuration File for Binkley v2.60 OS/2 ;=========================================================================== ; Port 2
Baud 115200
AnswerBack Gord Hannah
System Point: Marsh BBS (c)
Sysop Gord Hannah
Address 1:17/23.1
Boss 1:17/23
BossPhone 784-1945
BossPwd password
Nodelist f:\adept\mailer\nodelist\
Version7
StatusLog H:\LOGS\BINKLEY.LOG
Downloads H:\MAIL\INBOUND\
NetMail H:\MAIL\INBOUND\
NetFile H:\MAIL\INBOUND\
Hold H:\MAIL\OUTBOUND\
Prefix ATDT,
;
;========== Entries above this line should not be changed =======<PART 1>=== ; ;========== Entries below are taken from Binkley.add ============<PART 2>=== ; ;LockBaud 115200
AutoBaud
CaptureFile Stuff.CAP
Carrier 80
SLOWMODEM
NOCOLLIDE
PreInit |v``^``
Init ^,,,|ATQ0E0H0V1&C1S0=0S2=43X4|,,,
Suffix ,
Answer ATA|
Busy v,^,,ATH0|v
LogLevel 3
Gong
;Topview
Janusbaud 115200
MaxReq 6
Unattended
BoxType 1
Timeout 20
Colors 112 14 10 11 7 12 112 3
ScreenBlank
BBS Exit
SERIAL 100
;
;===========================================================================

I have a copy of XLaxNode ... what is the command line to get that
to compile a nodelist??

I don't use Xlax I use Qnode, so the best thing to do is pick up the archive and RTFM.

Hope this helps. Keep us posted.

We are a fine board trying to make it better.
http://www.pris.bc.ca/ghannah
ghannah@pris.bc.ca
Cheers! Gord
-=Team OS/2=-
--- Timed/2 2.30+
* Origin: Marsh BBS (c), Dawson Creek, BC Canada (1:17/23.1)

Something is amuck!!!

I want to use com/ip to run Bink over a telnet session, FrontDoor seems to
like com/ip alright ... bink on the other hand wants to look at my real modem and not the fake com/ip one.

I have set bink set to port 2, the fake telnet modem, and when bink loads it wants to use com 1...

BTW, do I need a fossil driver?? Seems to load fine with or without a fossil driver.

Joe

... Joe's Computer & BBS -=telnet.joesbbs.com=-
--- Platinum Xpress/Win/WINServer v3.0pr5
* Origin: Joe's Computer & BBS, Crystal River, Fl. -= telnet.joe (1:275/312)

HAHAHA I found the problem!!!!
I quoted your message to me ... see the word serial?? I thought that meant serial port.... should mention port number in stead!!!!

Thanx
Joe
On Feb 11, 2003 08:19am, GORD HANNAH wrote to IB JOE:

; BINKLEY CONTROL FILE
;
Serial 1234
System Your BBS Name Here
Sysop Your Name Here

... Joe's Computer & BBS -=telnet.joesbbs.com=-
--- Platinum Xpress/Win/WINServer v3.0pr5
* Origin: Joe's Computer & BBS, Crystal River, Fl. -= telnet.joe (1:275/312)

Replying to a message from IB JOE 1:275/312 to GORD HANNAH,

About RE: Config File, On Wed Feb 12 2003

I want to use com/ip to run Bink over a telnet session, FrontDoor
seems to like com/ip alright ... bink on the other hand wants to
look at my real modem and not the fake com/ip one.

BTW, do I need a fossil driver?? Seems to load fine with or without
a fossil driver.

If in DOS yes I used BNU for years with no problems, In OS/2 you will need SIO,
and you could use vmodem from that package. If windows sorry can't help some one else will need to address that.

I don't do windows.

Hope this helps. Keep us posted.

We are a fine board trying to make it better.
http://www.pris.bc.ca/ghannah
ghannah@pris.bc.ca
Cheers! Gord
-=Team OS/2=-
--- Timed/2 2.30+
* Origin: Marsh BBS (c), Dawson Creek, BC Canada (1:17/23.1)